A fajlagos forgácsoló erő jellemzése vékonyforgácsleválasztás technológiai körülményei között, akusztikus emisszió és mikrokeménység mérés segítségével

Characterisation of the specific cutting force under the conditions of fine chip-removal with the help of acoustic emission and microhardness measurement

Authors

  • István POLYÁK
  • István BIRÓ

Keywords:

cutting, specific cutting force, specific acoustic emission, microhardness, steel, /, forgácsolás, fajlagos forgácsolóerő, fajlagos akusztikus emisszió, mikrokeménység, acél

Abstract

The specific process parameters of cutting, which are specified to the uncut chip section, can provide important information about the materials’ expectable behaviour under cutting. Understanding the condition of fine-chip removal is especially important for the precision and micro cutting processes. In order to examine this special condition, a set of face grooving turning tests were carried out, where the removed material’s cross-section could be measured afterwards. The specific cutting force and specific acoustic emission calculated in this way (depending on the removed material layer’s thickness) deviate from the exponential characteristic when cutting with small uncut chip thickness. Microhardness measurements were realised to provide additional insight to what kind of changes occurred to the part’s machined surface layer.

Kivonat

Az elméleti forgáskeresztmetszetre fajlagosított folyamatjellemzői az anyagok forgácsolás során mutatott viselkedésének előrejelzéséhez szolgáltathatnak fontos információkat. A vékonyforgácsleválasztás technológiai körülményének ismerete különösképp lényeges precíziós és mikromegmunkálások esetén. E speciális körülmény vizsgálata céljából olyan beszúró homlokesztergálási kísérletsorozat került végrehajtásra, melynek előnye, hogy a leválasztott forgácskeresztmetszet utólagosan mérhető. Az így számított fajlagos forgácsoló erő és fajlagos akusztikus emisszió (az eltávolított rétegvastagság függvényében) az exponenciális jellegtől eltérnek a forgácsolás kis elméleti forgácsvastagságú szakaszában. Megtámogatandó ezen eredményeket, mikrokeménységmérésekkel vizsgáltuk a felület közeli anyagréteg változásának mértékét. 

References

I. Biró és T. Szalay, „Extension of empirical specific cutting force model for the process of fine chip-removing milling”, Int. J. Adv. Manuf. Technol., köt. 88, sz. 9, o. 2735–2743, febr. 2017, doi: 10.1007/s00170-016-8957-x.

D. E. Lee, I. Hwang, C. M. O. Valente, J. F. G. Oliveira, és D. A. Dornfeld, „Precision manufacturing process monitoring with acoustic emission”, Int. J. Mach. Tools Manuf., köt. 46, sz. 2, o. 176–188, febr. 2006, doi: 10.1016/j.ijmachtools.2005.04.001.

A. J. Mian, N. Driver, és P. T. Mativenga, „Chip formation in microscale milling and correlation with acoustic emission signal”, Int. J. Adv. Manuf. Technol., köt. 56, sz. 1, o. 63–78, szept. 2011, doi: 10.1007/s00170-011-3185-x.

X. Lu, Z. Jia, H. Wang, Y. Feng, és S. Y. Liang, „The effect of cutting parameters on micro-hardness and the prediction of Vickers hardness based on a response surface methodology for micro-milling Inconel 718”, Measurement, köt. 140, o. 56–62, júl. 2019, doi: 10.1016/j.measurement.2019.03.037.

Downloads

Published

2023-04-25