Minimálisan leválasztható rétegvastagság vizsgálata S960QL és C45E acélok ellenirányú marással történő megmunkálása során

Determination of minimum uncut chip thickness by means of conventional milling of S960QL, and C45E steels

Authors

  • PALÁGYI Imre
  • BIRÓ István

Keywords:

minimális leválasztható rétegvastagság, ellenirányú marás, forgácsolósebesség, előtolás, acél

Abstract

In this day and age technological advancements aim towards making small sized, compact products. This creates requirements for higher accuracy of machining procedures, where the minimum uncut chip thickness presents itself as a problem. The following research’s aim is to determine this minimum uncut chip thickness and its dependence of the cutting speed and feed rate by means of conventional milling with everyday-use sized tools.

Kivonat

A korszerű termékek fejlődése a miniatürizálás irányába folytatódik, az egyre kisebb méretű alkatrészek megfelelő pontosságú forgácsolása során felvetődik a minimális rétegvastagság problémája. Ez függ a forgácsolandó anyagtól, valamint a paraméterektől. Ezen rétegvastagság értékének meghatározását tűzi ki célul jelen kutatás, valamint az előtolás és forgácsoló sebesség hatásaira igyekszik eredményeket felmutatni, hagyományos méretű, ellenirányú megmunkálással.

References

M. Agmell, D. Johansson, S. V. A. Laakso, A. Ahadi, és J.-E. Ståhl, „The Influence the Uncut Chip Thickness has on the Stagnation Point in Orthogonal Cutting”, Procedia CIRP, köt. 58, o. 13–18, 0 2017, doi: 10.1016/j.procir.2017.03.183.

I. Biró és T. Szalay, „Extension of empirical specific cutting force model for the process of fine chip-removing milling”, Int. J. Adv. Manuf. Technol., köt. 88, 0 2017, doi: 10.1007/s00170-016-8957-x.

T. Mikołajczyk, H. Latos, D. Yu. Pimenov, T. Paczkowski, M. K. Gupta, és G. Krolczyk, „Influence of the main cutting edge angle value on minimum uncut chip thickness during turning of C45 steel”, J. Manuf. Process., köt. 57, o. 354–362, szept. 2020, doi: 10.1016/j.jmapro.2020.06.040.

I. Biró, T. Szalay, és N. Geier, „Effect of cutting parameters on section borders of the empirical specific cutting force model for cutting with micro-sized uncut chip thickness”, Procedia CIRP, köt. 77, o. 279–282, 0 2018, doi: 10.1016/j.procir.2018.09.015.

S. Wojciechowski, M. Matuszak, B. Powałka, M. Madajewski, R. W. Maruda, és G. M. Królczyk, „Prediction of cutting forces during micro end milling considering chip thickness accumulation”, Int. J. Mach. Tools Manuf., köt. 147, o. 103466, 0 2019, doi: 10.1016/j.ijmachtools.2019.103466.

J.-H. Lee és A. A. Sodemann, „Geometrical Simulation of Chip Production Rate in Micro-EndMilling”, Procedia Manuf., köt. 26, o. 209–216, 0 2018, doi: 10.1016/j.promfg.2018.07.029.

Downloads

Published

2021-04-20

Issue

Section

D. szekció – Gyártástudomány és technológia